How to Monitor Indoor Air Quality During Haze Season with TENMARS TM-380 Malaysia
How to Monitor Indoor Air Quality During Haze Season with TENMARS TM-380 Malaysia
During haze season in Malaysia, many people check the outdoor Air Pollution Index (API/AQI) before deciding whether to reduce outdoor activities or close windows and doors.
However, there is another important question:
What is the air quality inside your building?
Outdoor air quality readings do not necessarily represent the actual conditions inside an office, classroom, shop, warehouse or commercial building.
The TENMARS TM-380 Multi IAQ Monitor provides a practical way to check indoor PM2.5, PM10, CO₂, temperature and relative humidity using one portable instrument.
Outdoor AQI Does Not Tell You the Whole Indoor Story
During a haze episode, outdoor particulate pollution can enter buildings through:
Open doors
Open windows
Ventilation systems
Building entrances
Air leakage
Frequent movement of people between indoor and outdoor areas
The amount of particulate matter that remains indoors can vary considerably from one building to another.
Therefore, knowing that the outdoor AQI is high does not automatically tell you the PM2.5 concentration inside your office.
You need an indoor measurement to understand the actual indoor condition.
Why PM2.5 Is Important During Haze
PM2.5 refers to fine particulate matter with an aerodynamic diameter of approximately 2.5 micrometres or smaller.
During haze and other particulate pollution events, PM2.5 becomes an important parameter to monitor.
The TENMARS TM-380 uses a laser particulate matter sensor and measures both:
PM2.5
PM10
This allows users to investigate particulate conditions directly at the location being assessed.
A Simple Haze Monitoring Method
One useful approach is to take measurements at several locations.
For example:
Step 1 – Measure Outside the Building
Take a reading outside to establish a reference for current local conditions.
Step 2 – Measure Near the Main Entrance
Check whether particulate levels change around frequently opened doors or entrances.
Step 3 – Measure Inside the Office
Move further into the building and compare the PM2.5 and PM10 readings.
Step 4 – Measure Near the Air Purifier
If an air purifier is operating, compare readings near the unit with readings elsewhere in the room.
Step 5 – Check Different Rooms
Compare meeting rooms, offices, reception areas and other occupied spaces.
Instead of assuming that the entire building has the same air quality, this method helps identify differences between locations.
Don't Forget CO₂ When Closing Windows
During haze, a common response is to:
Close the windows and doors.
This may help reduce the entry of outdoor particulate pollution, depending on the building.
However, reducing outdoor air exchange can create another issue in occupied rooms:
CO₂ may increase.
People continuously produce carbon dioxide through respiration. In an occupied room with insufficient ventilation, CO₂ concentrations can rise.
This creates an important IAQ balancing problem.
You want to reduce the entry of outdoor particulate pollution while still maintaining appropriate ventilation.
This is one reason why a multi-parameter instrument can be more informative than a PM2.5-only meter.
PM2.5 Low, But CO₂ High?
Imagine an air-conditioned meeting room during a haze period.
The windows are closed.
An air purifier is operating.
PM2.5 readings decrease.
That sounds positive.
But after several people remain in the meeting room for an extended period, CO₂ begins to increase.
If you were measuring only PM2.5, you might conclude that the indoor air condition was satisfactory.
By monitoring PM2.5 and CO₂ together, you obtain more information about both particulate pollution and ventilation conditions.
Four Possible Indoor Conditions
1. Low PM2.5 + Low CO₂
Particulate conditions and ventilation indicators may both appear relatively favourable at the time of measurement.
2. High PM2.5 + Low CO₂
Ventilation may be providing sufficient outdoor air, but particulate pollution could be entering the building.
Investigate filtration, entrances, windows and other possible particle sources.
3. Low PM2.5 + High CO₂
Particulate filtration may be effective, but ventilation could require further investigation.
This situation may occur in heavily occupied enclosed rooms.
4. High PM2.5 + High CO₂
Both particulate pollution and ventilation conditions should be investigated.
The appropriate corrective action will depend on the building, HVAC system, occupancy and outdoor conditions.
Check Whether an Air Purifier Is Making a Difference
The TM-380 can also be used for basic before-and-after comparisons when evaluating an air purifier.
For example:
Before purifier operation → Record PM2.5
After operating for a period → Record PM2.5 again
Measurements can also be taken at different distances from the purifier.
This helps users observe whether particulate readings are changing rather than relying only on the purifier's fan speed or indicator light.
Monitor PM10 as Well
Haze monitoring discussions often concentrate heavily on PM2.5.
However, the TENMARS TM-380 also measures PM10.
Monitoring both particle fractions can provide additional information when investigating indoor particulate conditions.
This can also be useful in environments affected by dust from construction, renovation, traffic or other activities.
Temperature and Humidity Are Included
Indoor environmental conditions involve more than particles and CO₂.
The TM-380 also measures:
Temperature
Relative humidity
Facility teams can therefore observe these parameters while investigating indoor air quality.
This is particularly useful in air-conditioned buildings where ventilation, cooling and humidity control are interconnected.
Use Data Recording for Longer Investigations
Indoor air quality is not static.
Consider an office throughout the working day:
8:00 AM: Few employees have arrived.
10:00 AM: Occupancy increases.
12:00 PM: Doors open frequently during lunch.
3:00 PM: Meeting rooms become heavily occupied.
5:00 PM: Occupancy decreases.
A single reading cannot show all these changes.
The TENMARS TM-380 supports manual and automatic recording, making it possible to collect measurements over time for further evaluation.
Suitable Locations During Haze Season
The TM-380 can be used to investigate indoor conditions in:
Offices
Schools
Classrooms
Meeting rooms
Retail shops
Commercial buildings
Warehouses
Factories
Training centres
Public facilities
Air-conditioned workplaces
Useful for Facility and HVAC Teams
For facility managers and HVAC contractors, haze season can create competing requirements.
Buildings may need to reduce particulate entry while maintaining acceptable ventilation and indoor environmental conditions.
Being able to measure CO₂ + PM2.5 + PM10 + temperature + humidity with one instrument gives technicians more information for troubleshooting.
Don't Depend Only on Outdoor AQI
Outdoor AQI/API information remains valuable for understanding general outdoor pollution conditions.
But it should not automatically be treated as the exact air quality inside every building.
Different buildings have different:
Ventilation systems
Filtration efficiencies
Air leakage rates
Occupancy levels
Door-opening frequencies
Indoor particle sources
Air-cleaning equipment
Outdoor AQI tells you what is happening outside.
Indoor measurement tells you what is happening where people are actually working or studying.
TENMARS TM-380 for Haze Season Monitoring Malaysia
For organisations looking for a portable instrument to investigate indoor air conditions during haze periods, the TENMARS TM-380 combines several useful IAQ measurements in one unit.
It can measure:
CO₂ + PM2.5 + PM10 + Temperature + Humidity
This makes it suitable for indoor air quality investigations, HVAC checks, ventilation assessment and particulate monitoring in Malaysia.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
Contact MTM Precision for TENMARS TM-380 Multi IAQ Monitor enquiries in Malaysia.
13 Aug 2026