Asphalt Surface vs Internal Temperature: Why Use Myzox AST-10 Penetration Probe Malaysia
Asphalt Surface vs Internal Temperature: Why Use Myzox AST-10 Penetration Probe Malaysia
When measuring hot mix asphalt during road construction, one important question is whether contractors should check the surface temperature or the temperature inside the asphalt layer.
These two measurements are not necessarily the same.
The exposed pavement surface interacts directly with the surrounding environment, while asphalt below the surface may retain heat differently. For contractors who need penetration temperature measurement, the Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm needle probe provides a practical solution.
Understanding the difference between surface and internal temperature can help road contractors and QA/QC teams select the appropriate measurement method.
What Is Asphalt Surface Temperature?
Asphalt surface temperature refers to the temperature measured at or very close to the exposed surface of the pavement.
This can be measured using equipment such as:
Infrared thermometers
Infrared thermal instruments
Contact surface probes
Surface measurement can be useful when contractors need a quick indication of pavement surface temperature.
However, it does not automatically indicate the temperature deeper within the asphalt layer.
What Is Internal Asphalt Temperature?
Internal asphalt temperature refers to a temperature measured within the material.
A penetration-type thermocouple probe is inserted into the asphalt so that the sensor makes direct contact below the exposed surface.
The Myzox SE-IN Needle Probe is designed for this type of measurement.
It has a probe length of approximately:
200 mm
and a temperature measurement range of:
-50掳C to +650掳C
Myzox identifies the SE-IN as suitable for asphalt measurement.
Why Can Surface and Internal Temperatures Be Different?
After asphalt is placed, heat is transferred between the pavement and the surrounding environment.
The exposed surface is directly affected by air and weather, while deeper material is less directly exposed.
This can create temperature differences within the asphalt layer.
Several factors can contribute to these differences.
Wind
Wind increases heat transfer at the exposed pavement surface.
A windy construction site may therefore affect surface cooling differently from the asphalt underneath.
This is one reason a surface measurement should not automatically be treated as an internal asphalt temperature.
Ambient Temperature
The surrounding air temperature affects the rate at which hot asphalt loses heat.
Different paving conditions can therefore produce different cooling behaviour.
Actual measurements allow contractors to monitor conditions at the specific project location.
Rain and Moisture
Rain can significantly affect road paving operations.
Moisture and changing weather conditions can influence surface conditions and may cause construction work to be interrupted.
Temperature should therefore be monitored according to the project's approved procedure when weather conditions change.
Asphalt Layer Thickness
The thickness of the asphalt layer can influence how heat is retained and transferred.
A thicker layer may behave differently from a thinner layer.
This means contractors should not assume that all pavement sections cool at exactly the same rate.
Existing Pavement Temperature
During overlay and resurfacing works, hot asphalt is placed onto an existing pavement.
The temperature and condition of that existing surface can influence heat transfer from the new asphalt layer.
This is another reason why actual site measurements can be useful.
Time After Paving
Asphalt temperature changes continuously after placement.
A reading taken immediately behind the paver may differ from one taken later during the compaction process.
Recording both the temperature and measurement time provides more useful QA/QC information.
Penetration Thermometer vs Infrared Thermometer
These instruments use different measurement methods.
Infrared Thermometer
An infrared thermometer measures temperature without physically contacting the asphalt.
It primarily provides a surface temperature measurement.
Advantages can include:
Fast measurement
Non-contact operation
Convenient surface scanning
Myzox AST-10 with SE-IN Probe
The AST-10 uses a Type-K thermocouple probe that physically contacts the material.
With the SE-IN needle probe, users can perform penetration measurements within the asphalt.
Advantages include:
Direct contact measurement
Penetration into asphalt
200 mm probe length
Suitable for asphalt measurement
The correct choice depends on what the contractor actually needs to measure.
Does Penetration Measurement Replace Surface Measurement?
Not necessarily.
Surface and penetration measurements provide different information.
For some projects, one method may be sufficient. In other situations, both can provide useful information.
The appropriate method should follow the project's:
Specifications
QA/QC plan
Method statement
Inspection procedure
The key is to understand what each measurement represents.
Can Myzox AST-10 Measure Both?
The AST-10 supports different Type-K thermocouple probes.
For penetration measurement, the SE-IN Needle Probe is available with a range of:
-50掳C to +650掳C
For contact surface measurement, Myzox offers the optional SE-SU Surface Probe, with a range of:
-20掳C to +400掳C
This allows one AST-10 main instrument to support different measurement applications by changing the probe.
AST-10 Main Instrument Range
The Myzox AST-10 supports Type-K thermocouple measurements from:
-200掳C to +1,370掳C
However, users should remember that the actual usable range depends on the connected probe.
The probe's own specified temperature range must always be observed.
Why Is the 200 mm Probe Useful?
The SE-IN's 200 mm length gives users useful reach for penetration measurement.
This can be beneficial when checking hot asphalt because the sensor can make contact with material below the immediate exposed surface.
The actual insertion depth and measurement position should follow the applicable project procedure.
When Can Internal Asphalt Temperature Be Checked?
Depending on project requirements, penetration temperature measurements may be taken during:
Asphalt delivery
Paving
Placement
Behind-paver inspection
Before compaction
During rolling
Road resurfacing
Asphalt patching
The frequency and location of measurements should follow the approved QA/QC procedure.
Data Hold for Easier Field Measurement
The Myzox AST-10 includes a Data Hold function.
After taking a reading, the displayed value can be retained for easier viewing and recording.
This is useful when working around paving equipment or at measurement positions where immediate documentation is inconvenient.
MAX and MIN Functions
Additional AST-10 functions include:
MAX measurement
MIN measurement
Relative measurement mode
These provide extra flexibility when technicians are monitoring changing temperatures during road works.
FAQ: Is Asphalt Surface Temperature the Same as Internal Temperature?
Not necessarily.
Surface temperature can be affected directly by wind, air temperature and other environmental conditions, while material below the surface may retain heat differently.
The measurement method should therefore match the information required.
FAQ: Can an Infrared Thermometer Measure Inside Asphalt?
No. An infrared thermometer generally measures surface temperature.
To obtain a direct contact measurement within asphalt, a suitable penetration probe is required.
FAQ: What Probe Does Myzox AST-10 Use for Asphalt?
The Myzox SE-IN Needle Probe is suitable for asphalt measurement.
It is approximately 200 mm long and has a specified measurement range from -50掳C to +650掳C.
FAQ: Which Is Better for Asphalt QA/QC?
There is no universal answer.
If the QA/QC procedure requires surface temperature, use an appropriate surface measurement method.
If penetration temperature is required, the AST-10 with SE-IN probe is a suitable solution.
Always follow the relevant project specification.
Understanding What Your Asphalt Temperature Reading Means
A temperature reading is useful only when the contractor understands what has actually been measured.
Surface and internal asphalt temperatures represent different measurement locations and can therefore produce different results.
For Malaysian road contractors requiring direct penetration measurement, the Myzox AST-10 Digital Asphalt Thermometer with SE-IN 200 mm needle probe provides a practical way to check temperature within hot asphalt during paving, compaction and maintenance operations.
Myzox Authorized Distributor in Malaysia
MTM Precision Sdn. Bhd. is a Myzox Authorized Distributor in Malaysia, supplying Myzox surveying, civil engineering and road construction instruments.
Contact MTM Precision for product information, quotation and availability of the Myzox AST-10 Digital Asphalt Thermometer in Malaysia.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia.
Website: www.mtmpre.com.my
Email: mtmpre@yahoo.com
WhatsApp: +6016-6607346
Contact us for Myzox AST-10 Digital Asphalt Thermometer Malaysia, asphalt penetration temperature measurement and road construction QA/QC equipment.
16 Aug 2026