Linshang LS173 Portable Colorimeter for Delta E and Batch Color Consistency Malaysia
Linshang LS173 Portable Colorimeter for Delta E and Batch Color Consistency Malaysia
Maintaining the same color from one production batch to another can be difficult. Changes in raw materials, suppliers, pigments, processing conditions, printing parameters or coating processes may cause the finished product to look different from an approved reference.
The Linshang LS173 Portable Colorimeter provides manufacturers and quality control teams with an objective method for checking color difference and Delta E (ΔE) between samples.
For Malaysian manufacturers producing the same products repeatedly, the LS173 can be particularly useful for batch-to-batch color consistency control.
What Is Batch Color Consistency?
Batch color consistency means maintaining an acceptable color match across different production runs.
For example, a manufacturer may produce the same product in:
Batch 001 → January
Batch 002 → March
Batch 003 → June
Batch 004 → August
Although every batch follows the same specification, the actual finished colors may not be completely identical.
If products from different batches are eventually installed, assembled, packaged or displayed together, the variation may become noticeable.
Why Can Production Batches Have Different Colors?
Color variation can occur for many reasons, including:
Raw material variation
Pigment differences
Masterbatch variation
Supplier changes
Mixing ratios
Production temperature
Processing conditions
Paint formulation
Coating conditions
Printing parameters
Substrate variation
Some changes may be difficult to detect immediately with visual inspection alone.
Instrumental color measurement provides another way to monitor these differences.
Establish a Master Sample
For effective batch comparison, companies should establish an approved reference.
This may be:
Customer-approved sample
Golden sample
Master plastic component
Standard painted panel
Approved printed sample
Packaging reference
Previous approved production sample
Instead of comparing Batch 4 only against Batch 3, all batches can be compared against the same controlled master.
For example:
Master → Batch 1
Master → Batch 2
Master → Batch 3
Master → Batch 4
This provides a more consistent reference over time.
Using Delta E for Batch Comparison
Delta E (ΔE) expresses the measured difference between two colors.
Generally:
Smaller ΔE = closer color match
Larger ΔE = greater color difference
This makes Delta E useful for production batch comparison.
Instead of writing:
“Batch 004 looks slightly darker than Batch 003.”
the QC team can record measurable color difference information.
This can make quality records easier to compare and communicate.
Does a Higher Delta E Automatically Mean Reject?
No.
The acceptable Delta E tolerance depends on the actual application.
Different products can have very different requirements.
Factors may include:
Customer specification
Product type
Material
Appearance requirements
Manufacturing capability
Internal QC standards
Manufacturers should establish their own acceptance criteria rather than assuming that one Delta E limit applies universally.
Example: Plastic Injection Molding
Consider a manufacturer producing grey plastic housings throughout the year.
A master sample has already been approved by the customer.
For every new production batch, the QC department can measure selected samples with the LS173 and compare them with the master.
A workflow may be:
Master Sample → Measure
New Batch Sample → Measure
Review Color Difference → Within Established Tolerance?
If yes, the batch can continue through the normal QC process.
If not, the production team can investigate possible causes.
Example: Painted Metal Components
A factory produces painted metal enclosures every month.
Although the same paint specification is ordered, variation between paint batches or application conditions may influence the final color.
Using the LS173, suitable coated samples can be compared against the approved reference.
This provides an additional objective check alongside visual inspection.
Example: Packaging Repeat Orders
A company orders the same printed carton every few months.
The January batch is approved.
The next order arrives in May.
The third order arrives in September.
When products from all three batches are placed on the same retail shelf, inconsistent brand colors may become obvious.
By comparing each suitable batch against the same master sample, companies can improve long-term packaging color consistency.
Supplier-to-Supplier Consistency
Batch consistency becomes even more challenging when products are sourced from multiple suppliers.
For example:
Supplier A → Product Batch A
Supplier B → Product Batch B
Supplier C → Product Batch C
All three suppliers may claim to follow the same specification.
Using an approved master and an established measurement procedure provides a common reference for evaluating suitable samples from each supplier.
Incoming Quality Control
The LS173 can support Incoming Quality Control (IQC) for colored materials and components.
When a shipment arrives:
Receive Material → Sample Inspection → Measure Color → Compare Against Master → Release or Investigate
This helps identify potential variation before the material reaches production.
Production Monitoring
Batch consistency should not necessarily be checked only after production is completed.
Samples can be measured during the production run.
For example:
First Piece → Check
25% Production → Check
50% Production → Check
75% Production → Check
Final Sample → Check
The exact frequency should be determined by the company's QC procedure.
Regular checks can help identify color drift earlier.
Why Visual Memory Is Not Enough
Human beings are not particularly reliable at remembering exact colors over long periods.
An operator may remember that last month's product was “dark grey,” but this is not enough for precise comparison.
Even physical samples can change over time if they are poorly stored or exposed to unsuitable conditions.
For repeat manufacturing, companies should maintain controlled reference samples and defined measurement procedures wherever practical.
D/8 Measurement Geometry
The Linshang LS173 uses D/8 measurement geometry, referring to diffuse illumination with an 8-degree viewing geometry.
Controlled optical measurement helps improve repeatability compared with uncontrolled visual evaluation.
This can be especially useful when different QC operators need to inspect the same product specification.
Touch Screen for Routine Inspection
The LS173 features a touch-screen interface designed to make measurement information accessible during routine use.
For production environments, convenient operation is important because color measurement may need to be repeated many times across different samples and batches.
A portable instrument also allows measurement to be performed closer to incoming inspection, production or finished goods areas.
Color Consistency Across Different Departments
Objective measurement can also improve communication between departments.
Without measurement:
Sales: Customer says the color is wrong.
QC: It looks acceptable.
Production: We used the same settings.
Purchasing: Supplier says the material is unchanged.
With measurement data, teams have an additional common reference for investigating the issue.
Building a Batch Color Control System
A practical system can include:
1. Approved Master Sample
Keep a controlled reference.
2. Defined Measurement Location
Measure the same representative area whenever possible.
3. Defined Measurement Procedure
Ensure operators follow the same method.
4. Established Acceptance Criteria
Define suitable tolerances for the product.
5. Regular Production Checks
Measure according to the company's inspection frequency.
6. Record Results
Maintain records where traceability is required.
7. Investigate Trends
Do not only look for pass or fail. Increasing variation over several batches may indicate a developing process issue.
Which Industries Can Benefit?
Batch color consistency measurement may be useful for:
Plastic injection molding
Paint and coating
Printing
Packaging
Consumer products
Electrical components
Automotive components
Manufactured products
Supplier quality control
General industrial QC
Any manufacturer producing the same colored product repeatedly may benefit from more objective color comparison.
From Batch-to-Batch Variation to Controlled QC
The goal of a colorimeter is not simply to generate numbers.
The real value is creating a repeatable process:
Approved Standard → Measure → Compare → Record → Control
Over time, this can help manufacturers better understand their production consistency and identify color variation before it becomes a customer complaint.
Linshang LS173 Portable Colorimeter Malaysia
MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering and quality control applications throughout Malaysia.
If your company needs a portable colorimeter for Delta E measurement, batch-to-batch comparison, supplier color inspection or production color consistency, contact MTM Precision to discuss your application.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
Looking for a Linshang LS173 Portable Colorimeter for batch color consistency in Malaysia? Contact MTM Precision for quotation, product information and application enquiries.
12 Aug 2026