Linshang LS173 Portable Colorimeter for Production Quality Control IPQC Malaysia

Linshang LS173 Portable Colorimeter for Production Quality Control IPQC Malaysia

 

Color problems are much easier to control when they are detected during production rather than after an entire batch has been completed.

 

The Linshang LS173 Portable Colorimeter can support In-Process Quality Control (IPQC) by allowing manufacturers to measure product color, compare production samples against an approved standard and monitor color difference during the manufacturing process.

 

For manufacturers in Malaysia producing plastic parts, painted components, packaging and other suitable colored products, regular color measurement can help identify process variation before it becomes a larger quality problem.

 

Why Measure Color During Production?

 

Many companies perform color inspection only at two stages:

 

Incoming Material → Final Product

 

The problem is that a significant amount of production can occur between these two inspections.

 

If color begins changing halfway through the production run, the issue may not be discovered until final QC.

 

By that point, hundreds or thousands of units may already have been produced.

 

IPQC introduces measurement during production itself.

 

A Simple Production Color Control Process

 

A manufacturer can establish checkpoints such as:

 

Approved Master Sample

 

↓

 

First-Off Production Sample

 

↓

 

25% Production Check

 

↓

 

50% Production Check

 

↓

 

75% Production Check

 

↓

 

Final Production Sample

 

The exact inspection frequency should be determined according to the company's process, production volume and quality requirements.

 

The important point is to monitor color throughout production instead of relying only on the final result.

 

What Can Cause Color Drift During Production?

 

Even when production begins with an acceptable sample, color can change later.

 

Possible causes include:

 

Raw material variation

 

Pigment concentration

 

Masterbatch consistency

 

Mixing ratio

 

Processing temperature

 

Machine parameters

 

Paint formulation

 

Coating conditions

 

Printing conditions

 

Substrate changes

 

Material replacement

 

Process adjustments

 

Regular measurement can help QC teams identify when a change begins to occur.

 

Using an Approved Master Sample

 

A controlled master sample should form the basis of the comparison.

 

This could be:

 

Customer-approved sample

 

Golden sample

 

Approved plastic component

 

Standard painted panel

 

Approved printed sample

 

Packaging reference

 

Approved production sample

 

Instead of comparing the current sample only with the previous sample, production samples can be compared against the same master.

 

This helps reduce gradual color drift over multiple production runs.

 

Delta E for Production Monitoring

 

Delta E (ΔE) provides a numerical indication of the difference between two measured colors.

 

In general:

 

Smaller ΔE = closer color match

 

Larger ΔE = greater color difference

 

This can be useful for production monitoring because QC personnel can observe whether color difference is remaining stable or gradually increasing.

 

For example:

 

Start of Production → Small Difference

 

Mid Production → Increasing Difference

 

Later Production → Further Increase

 

Even before the product reaches the company's rejection criteria, the trend may indicate that the process should be investigated.

 

Don't Use Delta E Only as Pass or Fail

 

One useful approach is to look at Delta E not only as a final acceptance number but also as a process indicator.

 

Suppose the company's established acceptance limit has not yet been exceeded, but measurements are consistently moving away from the approved master.

 

That trend may provide an early warning.

 

The production team can investigate:

 

Has the material changed?

 

Was more pigment added?

 

Has the process temperature changed?

 

Was a new batch of paint introduced?

 

Did the substrate change?

 

Were machine parameters adjusted?

 

This makes color measurement useful for process control, not just rejection.

 

Example: Plastic Injection Molding

 

Consider a manufacturer producing beige plastic housings.

 

The first-off sample matches the approved master.

 

After several hours, the QC team measures another sample and notices an increasing color difference.

 

Rather than waiting until the end of production, the team can investigate immediately.

 

Potential causes might include material mixing, processing conditions or changes in the production setup.

 

Early intervention can prevent a much larger quantity of questionable products from being manufactured.

 

Example: Paint and Coating Production

 

A factory is producing painted metal components.

 

The first batch looks correct, but the process continues throughout the day.

 

Periodic color measurement can help determine whether the coating appearance remains consistent.

 

Visual inspection can still be used for overall surface quality, while the LS173 provides numerical color comparison.

 

Where required, a gloss meter and coating thickness gauge can be used separately for gloss and coating thickness inspection.

 

Example: Printing and Packaging

 

Printing processes can also experience color changes during a production run.

 

Instead of checking only the first approved print and the final finished quantity, samples can be measured at defined intervals.

 

If color begins to shift, corrective action may be considered before a large quantity of packaging is produced.

 

First-Off Sample Inspection

 

The first production sample is especially important.

 

Before full production begins, the first-off sample can be compared with the approved master.

 

A typical process may be:

 

Set Up Machine → Produce First Sample → Visual Inspection → LS173 Measurement → Compare Against Master → Approve Production

 

This creates an additional control point before mass production.

 

Why D/8 Geometry Is Useful

 

The Linshang LS173 uses D/8 optical geometry, referring to diffuse illumination with an 8-degree viewing geometry.

 

Controlled optical measurement helps reduce the variability associated with changing environmental conditions and subjective visual judgement.

 

This is useful when measurements are performed repeatedly throughout a production shift.

 

Touch Screen for Routine QC

 

Production inspection instruments need to be practical.

 

The LS173's touch-screen interface provides convenient access to measurement information, making it suitable for routine QC applications where operators may need to inspect many samples.

 

Its portable design also allows the instrument to be used closer to the production area.

 

Different Operators, Same QC Procedure

 

Shift work can create another challenge.

 

For example:

 

Morning Shift → Operator A

 

Afternoon Shift → Operator B

 

Night Shift → Operator C

 

If inspection relies entirely on visual judgement, each operator may evaluate color slightly differently.

 

Using the same master sample, instrument and measurement procedure helps create greater consistency between shifts.

 

Reduce Scrap and Rework

 

Consider two scenarios.

 

Scenario A – Final Inspection Only

 

Production completes 5,000 units.

 

Final QC discovers a color problem.

 

The company now needs to sort, rework or reject a large quantity.

 

Scenario B – In-Process Measurement

 

QC identifies increasing color variation after 500 units.

 

Production investigates and corrects the process.

 

Although color measurement cannot prevent every manufacturing problem, earlier detection can significantly reduce the impact of process variation.

 

Build Color Measurement into Your IPQC SOP

 

A production color inspection SOP can define:

 

Approved master sample

 

First-off inspection procedure

 

Measurement location

 

Number of measurements

 

Inspection frequency

 

Delta E or other acceptance criteria

 

Warning level

 

Rejection level

 

Measurement records

 

Corrective action procedure

 

This turns the colorimeter into part of the manufacturing control system.

 

IQC + IPQC + OQC

 

For stronger color quality control, measurement can be used throughout the entire manufacturing process:

 

IQC – Incoming Quality Control

 

Check incoming materials and supplier components.

 

↓

 

IPQC – In-Process Quality Control

 

Monitor color during production.

 

↓

 

OQC – Outgoing Quality Control

 

Confirm finished product color before shipment.

 

This creates a complete color inspection chain rather than relying on a single final measurement.

 

Who Can Use the Linshang LS173 for IPQC?

 

The LS173 may be considered by:

 

Plastic injection molding companies

 

Paint and coating manufacturers

 

Printing companies

 

Packaging manufacturers

 

Consumer product manufacturers

 

Automotive component manufacturers

 

Electrical component manufacturers

 

QA and QC departments

 

Production engineers

 

Process engineers

 

It is particularly useful where color consistency needs to be monitored repeatedly during production.

 

From Final Inspection to Process Control

 

The traditional approach asks:

 

“Did the finished batch pass?”

 

A stronger process-control approach also asks:

 

“Is the color remaining stable while we are producing it?”

 

This is where portable color measurement can provide additional value.

 

By monitoring production rather than simply inspecting the final result, manufacturers can identify potential color variation earlier and respond more effectively.

 

Linshang LS173 for Production Quality Control Malaysia

 

MTM Precision supplies industrial testing and measurement instruments for manufacturing, engineering and quality control applications throughout Malaysia.

 

If your company needs a portable colorimeter for IPQC, production color monitoring, Delta E measurement, first-off inspection or batch color consistency, contact MTM Precision to discuss your application.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

 

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346

 

Looking for a Linshang LS173 Portable Colorimeter for production quality control in Malaysia? Contact MTM Precision for quotation, product information and application enquiries.


 

12 Aug 2026