How to Check the Best Solar Panel Angle Using a Solar Power Meter Malaysia

How to Check the Best Solar Panel Angle Using a Solar Power Meter Malaysia

 

Solar panel angle can influence how much solar radiation reaches the surface of a photovoltaic module. Even when two panels are installed at the same location, differences in tilt and orientation can result in different levels of solar exposure.

 

A portable instrument such as the TENMARS TM-206A Solar Power Meter can be used to compare solar irradiance at different angles, providing useful field information for solar PV installers, technicians and engineers in Malaysia.

 

Why Does Solar Panel Angle Matter?

 

Solar panels generate electricity from sunlight reaching the photovoltaic modules.

 

The amount of solar radiation received depends partly on the relationship between:

 

Sun position

 

Panel orientation

 

Panel tilt angle

 

Time of day

 

Season

 

Surrounding shading

 

Weather conditions

 

A panel positioned more favourably toward incoming sunlight may receive higher irradiance than another panel at a less suitable angle.

 

This is why panel orientation and tilt are important considerations during solar PV installation.

 

What Does a Solar Power Meter Measure?

 

The TENMARS TM-206A measures solar radiation reaching its sensor.

 

Solar irradiance can be displayed in:

 

W/m² — watts per square metre

 

The TM-206A has a measurement range up to 1999 W/m², making it suitable for outdoor solar radiation measurements.

 

Instead of judging sunlight intensity visually, technicians can obtain numerical readings for comparison.

 

How to Compare Different Solar Panel Angles

 

A simple field comparison can be performed using the TM-206A.

 

Step 1: Choose the Test Location

 

Perform the measurements near the proposed solar panel installation area.

 

Make sure there are no unexpected shadows from:

 

Buildings

 

Trees

 

Roof structures

 

Antennas

 

Water tanks

 

The technician performing the measurement

 

Step 2: Position the Solar Power Meter

 

Orient the sensing surface to represent the proposed plane of the solar panel.

 

The orientation of the sensor should be controlled carefully because changing the angle can change the measured irradiance.

 

Step 3: Record the First Reading

 

Take a solar irradiance measurement at the first proposed angle.

 

For example:

 

Angle A: 760 W/m²

 

Record the result.

 

Step 4: Change the Angle

 

Adjust the sensor to represent another proposed panel position.

 

For example:

 

Angle B: 835 W/m²

 

Step 5: Compare Additional Positions

 

Continue with another angle if required.

 

For example:

 

Angle C: 905 W/m²

 

Under the conditions at that particular moment:

 

Angle A = 760 W/m²

Angle B = 835 W/m²

Angle C = 905 W/m²

 

Angle C receives the strongest solar irradiance during this specific comparison.

 

One Measurement Is Not Enough for System Design

 

An important point is that the sun's position changes throughout the day and throughout the year.

 

The angle producing the highest reading at noon on one particular day is not automatically the best year-round solar panel angle.

 

Professional PV system design should also consider:

 

Geographic location

 

Roof direction

 

Seasonal solar path

 

Morning and afternoon exposure

 

Shading throughout the day

 

Structural limitations

 

Drainage and maintenance access

 

Long-term energy production requirements

 

The TM-206A should therefore be used as a field measurement and comparison tool, rather than as the only basis for PV system design.

 

Compare Measurements Under Similar Conditions

 

Malaysia's weather can change quickly.

 

If Angle A is measured under clear sunlight but Angle B is measured just as a cloud passes overhead, the comparison will not be meaningful.

 

For better results:

 

Take readings close together in time

 

Avoid rapidly changing weather where possible

 

Repeat measurements

 

Maintain consistent test procedures

 

Record weather conditions

 

Avoid accidental sensor shading

 

This improves the reliability of the comparison.

 

Finding Areas with Better Solar Exposure

 

The same method can be used to compare different roof locations.

 

For example:

 

Roof Area A: 880 W/m²

Roof Area B: 720 W/m²

Roof Area C: 895 W/m²

 

The lower reading at Area B may indicate shading or a less favourable orientation at the time of measurement.

 

Further inspection can then determine the reason.

 

Useful for Existing Solar PV Systems

 

Solar power meters are not only useful before installation.

 

Technicians maintaining existing systems can use irradiance measurements when investigating:

 

Unexpectedly low PV output

 

New shading conditions

 

Changes caused by nearby construction

 

Vegetation growth

 

Differences between panel arrays

 

Performance complaints

 

If a solar array receives strong irradiance but produces unusually low output, the technician can investigate the electrical system and PV modules further.

 

Solar Irradiance vs PV Output

 

It is important to understand that solar irradiance and electrical output are different measurements.

 

Solar Power Meter

 

Measures the solar radiation reaching the measurement surface.

 

PV Electrical Test Equipment

 

Measures electrical parameters produced by the solar PV system.

 

Using both types of information provides a more complete understanding of system conditions.

 

Who Can Use the TENMARS TM-206A?

 

The TM-206A is suitable for:

 

Solar PV installers

 

Solar maintenance contractors

 

Electrical contractors

 

Energy consultants

 

Facility management teams

 

Engineering companies

 

Universities

 

Technical colleges

 

Building maintenance departments

 

Its handheld design makes it convenient for field comparison and routine solar radiation measurement.

 

Solar Power Meter Supplier in Malaysia

 

For professionals who need a portable instrument to measure solar radiation or compare solar exposure at different positions, the TENMARS TM-206A Solar Power Meter provides a practical solution.

 

MTM Precision supplies professional solar, electrical, environmental and industrial testing equipment in Malaysia.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346


 

15 Aug 2026