How to Measure Solar Transmission Through Automotive Glass Malaysia

How to Measure Solar Transmission Through Automotive Glass Malaysia

 

Automotive glass and window tint can significantly affect how much solar radiation enters a vehicle. In Malaysia's hot and sunny climate, solar control performance is an important consideration for vehicle owners, tint installers and automotive service providers.

 

The TENMARS TM-206A Solar Power Meter can be used to compare solar radiation before and after sunlight passes through automotive glass or window film.

 

This provides a simple numerical method for demonstrating differences between untreated glass and different types of solar film.

 

Why Measure Solar Transmission Through Car Glass?

 

When a vehicle is parked or driven under strong sunlight, solar radiation enters through the windows and contributes to heat build-up inside the cabin.

 

Automotive solar films are designed to reduce part of this incoming solar energy.

 

However, it can be difficult to judge solar performance simply by looking at the tint.

 

A darker film does not automatically mean that it provides proportionally better solar control.

 

Measurement provides a more objective comparison.

 

Using the TENMARS TM-206A

 

The TENMARS TM-206A is designed to measure solar radiation.

 

It provides readings in:

 

W/m虏

 

BTU/(ft虏路h)

 

with a measurement range up to 1999 W/m虏.

 

For automotive applications, the meter can be used to compare direct solar radiation against the radiation measured after sunlight passes through the vehicle glass.

 

Basic Automotive Glass Test

 

A simple comparative test can be performed as follows.

 

Step 1: Measure the Incoming Solar Radiation

 

Position the sensor so that it receives direct sunlight.

 

For example:

 

Incoming solar radiation: 950 W/m虏

 

Record the measurement.

 

Step 2: Measure Behind the Automotive Glass

 

Move the sensor behind the vehicle glass while keeping the measurement direction as consistent as possible.

 

For example:

 

After automotive glass: 620 W/m虏

 

The lower reading indicates that part of the incoming solar radiation has been reduced before reaching the sensor.

 

Step 3: Test Glass with Solar Film

 

The same method can be used on a window fitted with solar film.

 

For example:

 

Incoming solar radiation: 950 W/m虏

 

After tinted glass: 285 W/m虏

 

The difference provides a practical indication of how the tested glass-and-film combination affects transmitted solar radiation under those measurement conditions.

 

Comparing Different Window Films

 

Tint installers may also use the TM-206A to compare different products.

 

For example:

 

Direct sunlight: 900 W/m虏

 

Film A: 430 W/m虏

Film B: 310 W/m虏

Film C: 240 W/m虏

 

Under the same test conditions, Film C allows the lowest measured solar radiation to reach the sensor.

 

This can help customers see measurable differences between products instead of relying only on appearance or sales descriptions.

 

Before-and-After Installation Testing

 

Another useful approach is to take measurements before and after installing solar film.

 

Before Installation

 

Measure the solar radiation transmitted through the original vehicle glass.

 

After Installation

 

Repeat the measurement through the same glass after the film has been installed.

 

The two results can then be shown to the customer.

 

This creates a straightforward before-and-after demonstration.

 

Why Test Conditions Matter

 

Outdoor solar radiation can change very quickly.

 

Cloud movement alone can cause significant changes in the reading.

 

For meaningful comparisons:

 

Perform measurements close together in time

 

Maintain the same sensor position

 

Maintain the same sensor angle

 

Avoid shadows

 

Use the same glass orientation

 

Repeat measurements when necessary

 

If sunlight changes significantly between tests, repeat the comparison.

 

Solar Power Measurement Is Not the Same as VLT

 

This distinction is important.

 

Visible Light Transmission (VLT) refers to the amount of visible light passing through glass or window film.

 

A solar power meter measures solar radiation intensity.

 

Therefore, the TENMARS TM-206A should not be described as a replacement for a dedicated VLT or automotive tint meter when the objective is to verify visible-light transmission.

 

The instruments measure different properties.

 

What About IR Rejection?

 

Another common specification in automotive tinting is infrared rejection.

 

Again, a general solar power meter should not automatically be treated as a dedicated infrared rejection meter.

 

The TM-206A is useful for practical solar radiation comparison, while specialised instruments may be required when testing specific optical characteristics such as:

 

Visible Light Transmission

 

UV transmission

 

Infrared transmission

 

Choosing the correct instrument depends on what needs to be measured.

 

Useful Demonstration Tool for Tint Shops

 

The TM-206A can be particularly useful as a customer demonstration instrument.

 

Instead of discussing only technical specifications, an installer can demonstrate how much the solar radiation reading changes when different materials are placed between the sunlight and the sensor.

 

This can make product differences easier for customers to understand.

 

Other Glass Applications

 

The same measurement concept can be applied beyond automotive glass.

 

Potential applications include:

 

Residential windows

 

Office glass

 

Shopfront glass

 

Factory windows

 

Building fa莽ades

 

Solar control glazing

 

Architectural solar film

 

This makes the TM-206A useful for both automotive and building-related solar transmission comparisons.

 

Who Can Use the TENMARS TM-206A?

 

Potential users include:

 

Automotive tint shops

 

Solar film installers

 

Automotive workshops

 

Glass suppliers

 

Building contractors

 

Facility management companies

 

Engineering laboratories

 

Solar PV contractors

 

The same instrument can also be used for solar irradiance measurements related to photovoltaic installations.

 

Solar Power Meter Supplier Malaysia

 

For businesses that need a portable instrument to compare solar radiation through automotive glass, window tint or other transparent materials, the TENMARS TM-206A Solar Power Meter provides a practical field measurement solution.

 

MTM Precision supplies professional testing and measurement instruments for automotive, solar, building, environmental and industrial applications throughout Malaysia.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

 

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

πŸ“§ Email: mtmpre@yahoo.com

πŸ“± WhatsApp: +6016-660 7346


 

15 Aug 2026