Why Solar Irradiance Measurement Matters Before Solar PV Installation Malaysia
Why Solar Irradiance Measurement Matters Before Solar PV Installation Malaysia
Before installing a solar photovoltaic system, contractors normally evaluate available roof space, panel orientation, shading, electrical requirements and expected energy production. One additional field measurement that can provide useful information is solar irradiance.
Solar irradiance indicates the amount of solar power reaching a surface and is commonly measured in W/m².
The TENMARS TM-206A Solar Power Meter allows solar installers, engineers and technicians to perform portable solar radiation measurements during site assessment and installation work in Malaysia.
Why Measure Sunlight Instead of Just Looking at It?
Two areas of the same roof may appear equally bright but may not receive exactly the same solar radiation.
Differences can be caused by:
Roof orientation
Panel angle
Nearby buildings
Trees
Water tanks
Roof structures
Partial shading
Time of day
Visual inspection remains important, but actual irradiance readings provide numerical information that can be recorded and compared.
What Is Solar Irradiance?
Solar irradiance describes the solar power received per unit area.
For solar PV applications, it is commonly expressed as:
W/m² — watts per square metre
For example, if a solar power meter displays:
850 W/m²
the sensor is receiving approximately 850 watts of solar radiation per square metre at that particular moment and orientation.
Using TENMARS TM-206A for Site Assessment
The TENMARS TM-206A can measure solar radiation up to 1999 W/m².
During a preliminary site assessment, technicians can take measurements at several potential installation locations.
For example:
Roof Area A: 870 W/m²
Roof Area B: 810 W/m²
Roof Area C: 620 W/m²
If Area C consistently produces lower readings under comparable conditions, technicians can investigate whether shading or orientation is responsible.
Identify Shading Before Installation
Shading is an important consideration in PV system design.
Potential shading sources include:
Trees
Adjacent buildings
Signboards
Water tanks
Antennas
Roof structures
Utility infrastructure
Some sources of shading may only affect the proposed solar array during certain periods of the day.
Field irradiance measurements can provide additional information when assessing these conditions.
Compare Different Panel Orientations
A solar power meter can also be positioned at different orientations to compare the amount of solar radiation reaching each measurement plane.
For example:
Position 1: 710 W/m²
Position 2: 825 W/m²
Position 3: 890 W/m²
Position 3 receives the highest irradiance under those particular test conditions.
This can support preliminary site assessment, although a single measurement should never be treated as proof of the best year-round PV orientation.
Why One Reading Is Not Enough
The sun's position changes continuously.
Solar irradiance also changes because of:
Cloud cover
Weather
Time of day
Season
Sensor orientation
Malaysia's tropical weather can produce particularly rapid changes when clouds move across the sun.
Therefore, professional solar system design should not rely on one instantaneous measurement.
Field measurements should be considered together with longer-term solar data, shading analysis, system design calculations and site conditions.
Establishing a Useful Reference
Irradiance measurements taken during installation can also provide useful reference information for future maintenance.
For example, a technician could record:
Solar Irradiance: 910 W/m²
PV Output: Recorded electrical output
Time: 1:15 PM
Weather: Clear
Shading: None observed
When the system is inspected later, similar measurements can help technicians understand whether reduced electrical output is associated with available sunlight or another issue.
Solar Irradiance and PV Troubleshooting
Consider two situations.
Situation A: Low Irradiance + Low PV Output
The system may simply be receiving insufficient sunlight because of weather or shading.
Situation B: High Irradiance + Low PV Output
Further investigation may be required.
Possible areas include:
Dirty modules
New shading
Damaged PV modules
Loose connections
DC wiring
Inverter operation
System configuration
The solar power meter does not diagnose these electrical problems directly.
Instead, it helps answer an important troubleshooting question:
How much solar radiation was available when the PV output was measured?
Useful for Commercial and Industrial Solar Projects
Solar PV is increasingly used across Malaysian commercial and industrial facilities.
Potential sites include:
Factories
Warehouses
Office buildings
Shopping centres
Schools
Commercial properties
Residential buildings
For contractors handling multiple sites, a handheld solar power meter can be a useful addition to the field measurement toolkit.
Solar Irradiance Meter vs Electrical Tester
These instruments perform different jobs.
A solar irradiance meter measures incoming solar radiation.
Electrical test instruments measure parameters associated with the PV electrical system.
For better PV assessment, technicians may use solar irradiance readings alongside electrical measurements rather than treating either measurement independently.
Why Use TENMARS TM-206A?
The TENMARS TM-206A is designed as a portable solar radiation measurement instrument.
It offers:
Solar radiation measurement
Range up to 1999 W/m²
W/m² measurement
BTU/(ft²·h) measurement
Portable handheld operation
Solar PV applications
Glass and solar film comparison applications
This makes it suitable for users who need a straightforward instrument for field solar measurements.
Who Can Use the TM-206A?
Potential users include:
Solar PV contractors
Electrical contractors
Solar maintenance companies
Energy consultants
Facility management teams
Engineering companies
Universities
Technical institutions
Building maintenance departments
Solar Irradiance Meter Supplier Malaysia
Solar irradiance measurement provides useful field information before PV installation and can remain valuable throughout the system's operating life.
For contractors, engineers and maintenance teams looking for a portable solution, the TENMARS TM-206A Solar Power Meter is suitable for solar radiation measurement and comparative testing.
MTM Precision supplies professional solar, electrical, environmental and industrial testing instruments in Malaysia.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
15 Aug 2026