How to Find the Best Solar Panel Position and Angle Using TENMARS TM-207 Malaysia
How to Find the Best Solar Panel Position and Angle Using TENMARS TM-207 Malaysia
Solar panel performance depends not only on the quality of the PV module but also on how much solar radiation actually reaches its surface.
Panel position, orientation, tilt angle, surrounding buildings and shading can all influence the available solar irradiance.
The TENMARS TM-207 Solar Power Meter provides a practical way for solar installers and technicians to compare solar radiation at different positions and angles directly on site.
Why Solar Panel Position Matters
Two solar panels installed on the same property may receive different levels of solar radiation.
The difference can be caused by:
Roof orientation
Panel tilt
Nearby buildings
Trees
Water tanks
HVAC equipment
Antennas
Roof structures
Partial shading
This is why choosing a suitable installation position is important during solar PV planning.
Why Visual Inspection Is Not Enough
A rooftop may appear to receive strong sunlight, but the human eye cannot determine solar irradiance in W/m².
A solar power meter provides an actual measurement.
Instead of saying:
“This position looks better.”
A technician can compare actual readings from different positions.
This makes site assessment more objective.
Using the TENMARS TM-207
The TENMARS TM-207 is designed for solar radiation measurement and can measure up to 1999 W/m².
For solar PV applications, readings can be taken at different positions around the proposed installation area.
The technician can then compare the results under similar sunlight conditions.
Step 1: Select Possible Installation Positions
Identify several suitable locations for the solar panels.
For example:
Roof Section A
Roof Section B
Roof Section C
Open rooftop area
Area near rooftop equipment
Take solar irradiance measurements at each location.
This provides an initial comparison of the available solar radiation.
Step 2: Keep Measurement Conditions Consistent
Solar conditions can change quickly because of clouds and changes in the sun's position.
When comparing different locations, measurements should therefore be taken as close together in time as practical.
Try to maintain similar sensor orientation and environmental conditions.
Consistent measurement technique produces more meaningful comparisons.
Step 3: Compare Different Angles
Solar radiation received by a surface depends on the angle between the surface and incoming sunlight.
The TM-207 can be used to compare irradiance at different sensor orientations.
For example, technicians can take measurements at several candidate angles and observe how the W/m² reading changes.
This can provide useful field information when evaluating panel orientation.
Step 4: Check for Partial Shading
Even when most of a rooftop is exposed to sunlight, certain sections may experience shading.
Possible sources include:
Adjacent buildings
Trees
Water tanks
Chimneys
Signboards
Antennas
Air-conditioning systems
Other rooftop equipment
Measure an unobstructed area first.
Then compare it with the potentially affected area.
The difference can help identify the immediate effect of shading at the time of inspection.
Step 5: Repeat Measurements at Different Times
One measurement represents conditions at that particular moment.
Shadows move throughout the day.
A location that receives full sunlight in the morning may experience shading later.
For a more useful site assessment, measurements can be repeated at different times.
This is particularly important when surrounding structures could create changing shadows.
Can TM-207 Determine the Perfect Solar Panel Angle?
Not by itself.
The TM-207 is a measurement instrument, not complete solar PV design software.
Final solar panel orientation and tilt should consider factors such as:
Geographic location
Roof structure
Long-term solar data
Seasonal variation
System design
Installation limitations
Local engineering requirements
The TM-207 is best used to provide actual field measurements that support the assessment.
Solar Irradiance Meter vs Lux Meter
A lux meter measures visible illuminance.
A solar power meter measures solar radiation intensity.
For evaluating solar energy conditions, W/m² is the more relevant measurement.
Therefore, technicians should not assume that a high lux reading automatically provides the solar irradiance information required for PV assessment.
Useful for Existing Solar PV Systems Too
The TM-207 is not limited to new installations.
It can also assist technicians investigating an existing PV system.
If one part of an installation appears to perform differently, irradiance measurements can help determine whether the panels are experiencing different sunlight conditions.
The technician can then investigate other possible causes such as:
Panel contamination
Electrical faults
Cable problems
Inverter issues
Panel temperature
Shading
Solar irradiance becomes one part of a broader troubleshooting process.
Who Can Use the TENMARS TM-207?
The TM-207 is suitable for users such as:
Solar PV installers
Electrical contractors
Solar maintenance teams
Energy consultants
Facility managers
Building engineers
Maintenance departments
Engineering students
Technical training centres
Its portable design is useful for technicians who need quick measurements at multiple locations.
Practical Solar Measurement for Malaysia
Malaysia has strong potential for solar PV across residential, commercial and industrial properties.
As more solar systems are installed, professional measurement becomes increasingly important.
Solar contractors already use electrical instruments to test voltage, current, insulation and other parameters.
Adding solar irradiance measurement provides another useful piece of information about the actual environmental conditions affecting the PV installation.
From Guessing to Measuring
The biggest advantage of a solar power meter is simple.
Instead of judging sunlight only by eye, technicians can obtain a measurable value.
With the TENMARS TM-207 Solar Power Meter, different positions, orientations and shading conditions can be compared directly in W/m².
For solar PV contractors in Malaysia, this can support more professional site assessment, installation and troubleshooting work.
Looking for TENMARS TM-207 Solar Power Meter in Malaysia?
MTM Precision supplies professional testing and measurement instruments for solar PV, electrical, environmental, building and industrial applications.
Contact us for TENMARS TM-207 Solar Power Meter pricing, availability and product information in Malaysia.
Contact MTM Precision
MTM Precision Sdn. Bhd.
Showroom & Service Centre
No. 29-1 & 29-2, Jalan Bandar 18,
Pusat Bandar Puchong,
47160 Puchong, Selangor, Malaysia
🌐 Website: www.mtmpre.com.my
📧 Email: mtmpre@yahoo.com
📱 WhatsApp: +6016-660 7346
15 Aug 2026