TENMARS TM-207 for Solar Panel Site Assessment Malaysia

TENMARS TM-207 for Solar Panel Site Assessment Malaysia

 

Before installing a solar PV system, one of the most important questions is simple:

 

How much solar radiation is actually available at the proposed installation area?

 

A location may look sunny, but nearby buildings, trees, rooftop structures, panel orientation and temporary shading can affect the amount of solar radiation reaching the surface.

 

The TENMARS TM-207 Solar Power Meter provides a practical way to measure solar irradiance directly at the site and display the result in W/m².

 

Why Solar Site Assessment Matters

 

Solar PV systems depend on available solar energy.

 

Two locations on the same building can experience different solar conditions because of:

 

Building orientation

 

Roof geometry

 

Nearby high-rise buildings

 

Trees

 

Water tanks

 

HVAC equipment

 

Signboards

 

Rooftop structures

 

Temporary shading

 

Visual inspection is useful, but a solar power meter adds an actual measurement to the assessment.

 

Using TENMARS TM-207 for Preliminary Site Assessment

 

The TM-207 is a handheld solar radiation meter with a measurement range of up to 1999 W/m².

 

For preliminary solar PV assessment, technicians can take readings at several points around a proposed installation area.

 

For example:

 

Point A — Open rooftop

Measure solar irradiance in an unobstructed section.

 

Point B — Near rooftop equipment

Check whether nearby structures affect the reading.

 

Point C — Near building edge

Compare exposure with the central rooftop area.

 

Point D — Potentially shaded area

Measure the difference between shaded and unobstructed positions.

 

This provides useful field information when comparing potential panel locations.

 

Measure in W/m²

 

Solar irradiance is commonly expressed in watts per square metre (W/m²).

 

The TM-207 provides direct W/m² measurement, making the result more relevant to solar radiation assessment than simply measuring visible brightness.

 

This distinction is important because:

 

Solar irradiance is not the same as lux.

 

Lux describes visible illuminance as perceived by the human eye, while W/m² describes radiant power received over an area.

 

Compare Different Roof Areas

 

Large commercial and industrial buildings may have several possible locations for solar panels.

 

Instead of assuming that every part of the roof receives identical solar exposure, technicians can use the TM-207 to compare different areas.

 

This can be particularly useful for:

 

Factories

 

Warehouses

 

Shopping centres

 

Office buildings

 

Schools

 

Hospitals

 

Commercial properties

 

Residential buildings

 

The measurements can help identify differences that deserve further investigation during system planning.

 

Check the Effect of Shading

 

Shading is an important consideration in solar PV installations.

 

Common sources include:

 

Trees

 

Adjacent buildings

 

Water tanks

 

Antennas

 

Exhaust systems

 

Air-conditioning equipment

 

Roof structures

 

Using the TM-207, a technician can compare solar irradiance in an open location with the reading in an affected location.

 

This provides a simple way to demonstrate the immediate effect of shading under the conditions present during the measurement.

 

Compare Panel Orientation

 

Solar radiation received by a surface changes according to its orientation relative to incoming sunlight.

 

The TM-207 can therefore be used to compare measurements at different orientations or angles.

 

For preliminary assessment, this is useful when technicians want to understand how changing the measurement surface affects the available irradiance.

 

However, a single handheld measurement should not replace professional solar PV design calculations or longer-term solar resource data.

 

It is best used as a practical field verification and comparison tool.

 

Existing Solar PV System Inspection

 

The TM-207 can also be useful after a solar PV installation has been completed.

 

If a customer reports lower-than-expected output, technicians may want to investigate environmental conditions around the installation.

 

Solar irradiance measurements can be considered together with other checks such as:

 

Panel condition

 

Shading

 

Dirt or contamination

 

Electrical measurements

 

Inverter performance

 

Cable condition

 

Panel temperature

 

This helps provide a more complete troubleshooting process.

 

Why Portable Measurement Is Useful

 

A portable instrument allows technicians to move around the installation site and quickly compare multiple positions.

 

This makes the TM-207 suitable for field work where the objective is to obtain immediate solar radiation measurements without setting up a complex monitoring system.

 

Potential users include:

 

Solar PV installers

 

Solar contractors

 

Electrical contractors

 

Energy consultants

 

Facility management teams

 

Building inspectors

 

Maintenance engineers

 

Technical colleges and universities

 

Solar PV Opportunities in Malaysia

 

Malaysia's climate makes solar energy an important area for residential, commercial and industrial energy projects.

 

As solar PV installations increase, supporting measurement instruments also become more relevant.

 

Contractors increasingly need instruments not only for electrical testing but also for assessing the environmental conditions affecting solar PV performance.

 

A solar power meter such as the TENMARS TM-207 can become part of that field testing toolkit.

 

A Simple Tool for Better Solar Site Decisions

 

The TENMARS TM-207 does not replace a complete solar PV design study.

 

Instead, its strength is providing technicians with a quick and measurable way to compare actual solar radiation conditions at the site.

 

Rather than relying only on:

 

“This area looks sunny.”

 

Technicians can obtain an actual:

 

W/m² measurement.

 

That makes solar site assessment more measurable, repeatable and professional.

 

Looking for TENMARS TM-207 Solar Power Meter in Malaysia?

 

MTM Precision supplies professional testing and measurement equipment for solar PV, electrical, environmental, industrial and building applications.

 

For TENMARS TM-207 Solar Power Meter enquiries, pricing or product availability in Malaysia, contact our team.

 

Contact MTM Precision

 

MTM Precision Sdn. Bhd.

Showroom & Service Centre

No. 29-1 & 29-2, Jalan Bandar 18,

Pusat Bandar Puchong,

47160 Puchong, Selangor, Malaysia

 

🌐 Website: www.mtmpre.com.my

📧 Email: mtmpre@yahoo.com

📱 WhatsApp: +6016-660 7346


 

15 Aug 2026